View LP101WH1-TLA1_4360113.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification lp101wh1 liquid crystal display specification for approval title 10.1 hd tft lcd customer sony model supplier lg display co., ltd. *model lp101wh1 suffix tla1 ( ) preliminary specification ( ) final specification ver. 0.2 mar. 04, 2009 1 / 28 suffix tla1 *when you obtain standard approval, please use the above model name without suffix approved by signature // / please return 1 copy for your confirmation with your signature and comments. products engineering dept. lg display co., ltd prepared by reviewed by signature approved by c. j. jun / manager p. a. choi / engineer s. w. paeng / manager www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display contents no item page cover 1 contents 2 record of revisions 3 1 general description 4 2 absolute maximum ratings 5 3 electrical specifications 3-1 electrical charactreistics 6 3-2 interface connection 7 3-3 lvds signal timing specifications 8 ver. 0.2 mar. 04, 2009 2 / 28 3-4 signal timing specifications 10 3-5 signal timing waveforms 10 3-6 color input data refernece 11 3-7 power sequence 12 4 optical sfecifications 13 5 mechanical characteristics 16 6 reliablity 20 7 international standards 7-1 safety 21 7-2 emc 21 8 packing 8-1 designation of lot mark 22 8-2 packing form 22 9 precautions 23 a appendix. enhanced extended display identification data 25 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display record of revisions revision no revision date page description edid ver 0.0 nov. 10. 2008 all first draft (preliminary specifi cation) - 0.1 feb. 18. 2009 7 36 pin(@ pin map) - 16 activer area dimension - 17 front view - 18 rear view - 25~27 edid - 0.2 mar. 04. 2009 5 add notes2(normal scanner operatio n) - 6 electrical characteristics - 7 vled voltage range - 12,13 power sequence 18 add active area & bezel open tolerance 19 cof location update on drawing ver. 0.2 mar. 04, 2009 3 / 28 19 cof location update on drawing www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 1. general description the lp101wh1 is a color active matrix liquid crystal display with an integral led backlight system. the matrix employs a-si thin film transistor as the active eleme nt. it is a transmissive type display operating in the normally white mode. this tft-lcd has 10.1inches diagon ally measured active display area with hd resolution(1366 horizontal by 768 vertical pixel array). e ach pixel is divided into red, green and blue sub- pixels or dots which are arranged in vertical stripes. gray s cale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. the lp101wh1 has been designed to apply the interface method that enables low power, high speed, low emi. the lp101wh1 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. in combination with the ver tical arrangement of the sub-pixels, the lp101wh1 characteristics provide an excellent flat displa y for office automation products such as notebook pc. tft-lcd panel (1366 x 768) 1 cn 1 user connector power block edid block gip(gate in panel) ver. 0.2 mar. 04, 2009 4 / 28 general features active screen size 10.1 inches diagonal outline dimension 235(h) 143(v) .5.2(d,max.) [mm] pixel pitch 0.16305mm 0.16305 mm pixel format 1366 horiz. by 768 vert. pixels rgb str ip arrangement color depth 6-bit, 262,144 colors luminance, white 200 cd/m 2 (typ.5 point) power consumption total 3.58 watt(typ.) @ lcm circuit 1.16 watt(ty p.), b/l input 2.42 watt(typ.) (w/o led driver) weight 200g (max.) display operating mode transmissive mode, normally w hite surface treatment glare treatment of the front polar izer rohs comply yes control & data power edid signal & power 768 1 1366 user connector 40 pin gip(gate in panel) source driver circuit led backlight assy lvds & timing control block pwm & vbl www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 2. absolute maximum ratings the following are maximum values which, if exceeded , may cause faulty operation or damage to the unit. table 1. absolute maximum ratings parameter symbol values units notes min max power input voltage vcc -0.3 4.0 vdc at 25 5 c operating temperature t op 0 50 c 1,2 storage temperature h st -20 60 c 1 operating ambient humidity h op 10 90 %rh 1 storage humidity h st 10 90 %rh 1 note : 1. temperature and relative humidity range a re shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. note : 2. not showing abnormal scanner operation wh en turning on lcd module after storage test at - 10 during 30min. ver. 0.2 mar. 04, 2009 5 / 28 storage operation 10 20 30 40 50 60 70 80 0 -20 dry bulb temperature [ ] 10 % 20 % 40 % 60 % 90% 80% 0 10 20 30 40 50 60 wet bulb temperature [ ] humidity[(%)rh] at - 10 during 30min. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 3. electrical specifications 3-1. electrical characteristics table 2. electrical characteristics parameter symbol values unit notes min typ max module : power supply input voltage vcc 3.0 3.3 3.6 v dc power supply input current i cc - 350 402 ma 1 power consumption pc - 1.16 1.33 watt 1 differential impedance zm 90 100 110 ohm 2 led backlight ( with led driver ) : led driver ( @12v ) p driver - 0.21 0.25 watt operating voltage v led - 28.8 30.6 v operating current per string i led - 21 - ma 3 the lp101wh1 requires two power inputs. one is emp loyed to power the lcd electronics and to drive the tft array and liquid crystal. the second input whic h powers the led bl. ver. 0.2 mar. 04, 2009 6 / 28 note) 1. the specified current and power consumption are under the vcc = 3.3v , 25 , fv = 60hz condition whereas mosaic pattern is displayed and fv is the f rame frequency. 2. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 3. the typical operating current is for the typica l surface luminance (l wh ) in optical characteristics. i led is the current of each leds string, led backlight has 6 strings on it. 4. the led power consumption shown above does not i nclude power of external led driver circuit for typical current condition. 5. the life time is determined as the time at which brightness of led is 50% compare to that of initia l value at the typical led current. power consumption p bl - 2.42 2.57 watt 4 life time 15,000 hrs 5 led driver pwm input range specification: 12.5%(min .)~100%(max.) (pwm input frequency specification: 200hz~2khz) www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 3-2. interface connection table 3. module connector pin configuration (cn1) this lcd employs one interface connection, a 40 pin connector is used for the module electronics inter face. 1, interface chips 1.1 lcd : siw, 1port including lvds receiver 1.2 system : * pin to pin compatible with lvds 2. connector 2.1 lcd :i-pex 20455-040e-0* (locking type) or equivalent 2.2 mating : 2.3 connector pin arrangement 1 40 pin symbol description notes 1 ct1/nc connector test/no connection(reserved) 2 vdd +3.3v power supply 3 vdd +3.3v power supply 4 v edid +3.3v edid power 5 test panel self test 6 clk edid edid clock input 7 data edid edid data input 8 rxin0- lvds differential data input 9 rxin0+ lvds differential data input 10 gnd ground 11 rxin1- lvds differential data input 12 rxin1+ lvds differential data input 13 gnd ground 14 rxin2- lvds differential data input 15 rxin2+ lvds differential data input 16 gnd ground ver. 0.2 mar. 04, 2009 7 / 28 [lcd module rear view] 16 gnd ground 17 rxclkin- lvds differential clock input 18 rxclkin+ lvds differential clock input 19 gnd ground 20 nc no connection 21 nc no connection 22 gnd ground 23 nc no connection 24 nc no connection 25 gnd ground 26 nc no connection 27 nc no connection 28 gnd ground 29 nc no connection 30 nc no connection 31 vled_gnd led ground 32 vled_gnd led ground 33 vled_gnd led ground 34 ct2/nc connector test/no connection(reserved) 35 s_pwmin system pwm signal input(+3.3v swing) 36 bl_on led enable(3.3v input) [note 1] 37 nc no connection 38 vled 7~21v led power supply 39 vled 7~21v led power supply 40 vled 7~21v led power supply [note 1] let this pin nc if this pin is not used. (on: 2.0v ,off:0~0.4v) www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display description symb ol min max unit notes lvds differential voltage |v id | 100 600 mv - lvds common mode voltage v cm 0.6 1.8 v - lvds input voltage range v in 0.3 2.1 v - 3-3-1. dc specification 3-3. lvds signal timing specifications ver. 0.2 mar. 04, 2009 8 / 28 description symbol min max unit notes lvds clock to data skew margin t skew - 400 + 400 ps 85mhz > fclk 65mhz t skew - 600 + 600 ps 65mhz > fclk 25mhz lvds clock to clock skew margin (even to odd) t skew_eo - 1/7 + 1/7 t clk - maximum deviation of input clock frequency during ssc f dev - 3 % - maximum modulation frequency of input clock during ssc f mod - 200 khz - 3-3-2. ac specification www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display < clock skew margin between channel > f center f max f min f mod 1 f center * f dev freq. ver. 0.2 mar. 04, 2009 9 / 28 < lvds data format > 3-3-3. data format - lvds 1 port < spread spectrum > time g0 r5 r4 r3 r2 r1 r0 b1 b0 g5 g4 g3 g2 g1 de vsync hsync b5 b4 b3 b2 x b7 b6 g7 g6 r7 r6 r1 r0 g2 g1 b3 b2 r7 r6 g0 b1 de x current (nth ) cycle r5 r4 b0 g5 vsync hsync b7 b6 r3 r2 g4 g3 b5 b4 g7 g6 previous (n-1)th cycle next (n+1)th cycle rclk+ ra+/- rb+/- rc+/- rd+/- www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 3-4. signal timing specifications table 5. timing table this is the signal timing required at the input of the user connector. all of the interface signal ti ming should be satisfied with the following specifications and spe cifications of lvds tx/rx for its proper operation. item symbol min typ max unit note dclk frequency f clk 66.5 72.3 88.4 mhz hsync period thp 1430 1526 1586 tclk width t wh 16 32 40 width-active t wha 1366 1366 1366 vsync period t vp 775 790 950 thp width t wv 2 5 48 width-active t wva 768 768 768 data enable horizontal back porch t hbp 32 80 124 tclk horizontal front porch t hfp 16 48 56 vertical back porch t vbp 4 14 56 thp vertical front porch t vfp 1 3 28 ver. 0.2 mar. 04, 2009 10 / 28 3-5. signal timing waveforms condition : vcc =3.3v low: 0.3vcc high: 0.7vcc data enable, hsync, vsync hsync data enable vsync data enable t wh t hp t hfp t hbp t vp t wv t vbp t vfp t wha t wva t clk 0.5 vcc dclk www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 3-6. color input data reference the brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. t he table below provides a reference for color versus data input. table 7. color data reference color input color data red msb lsb green msb lsb blue msb lsb r 5 r 4 r 3 r 2 r 1 r 0 g 5 g 4 g 3 g 2 g 1 g 0 b 5 b 4 b 3 b 2 b 1 b 0 basic color black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 ver. 0.2 mar. 04, 2009 11 / 28 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red red (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green green (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 ... green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue blue (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 3-7. power sequence interface signal, v i lvds power supply input vcc 90% 10% 10% 0v 90% t 1 t 2 t 3 t 4 t 5 t 6 0v led on/off control signal led_en valid data 0v (off) 3-7-1. logic power and lvds signal sequence ver. 0.2 mar. 04, 2009 12 / 28 note) 1. valid data has to meet 3-3. lvds signal timing specifications 2. please avoid floating state of interface signal at invalid period. 3. when the interface signal is invalid, be sure to pull down the power supply for lcd vcc to 0v. 4. led power must be turn on after power supply for lcd and interface signal are valid. table 6. logic power sequence table parameter value units min. typ. max. t 1 0.5 - 10 ms t 2 0 - 50 ms t 3 0 - 50 ms t 4 400 - - ms t 5 200 - - ms t 6 200 - - ms www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display dimming control signal of led bl pwm led input voltage vled led on/off control signal led_en 0v (low) 0v 0v (off) t 7 t 9 t 10 t 8 valid data 90% 10% 3-7-2. led_en , pwn and led power sequence ver. 0.2 mar. 04, 2009 13 / 28 note) 1. control signal has to meet 3-1. electrical char acteristics table 7. led power sequence table parameter value units min. typ. max. t 7 10 - - ms t 8 0 - - ms t 9 0 - - ms t 10 10 - - ms www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 4. optical specification fig. 1 optical characteristic measurement equipment and method table 8. optical characteristics ta=25 c, vcc=3.3v, f v =60hz, f clk = 72.3mhz, i bl = 20 ma values lcd module optical stage(x,y) pritchard 880 or equivalent 50cm optical characteristics are determined after the unit has b een on and stable for approximately 30 minutes in a dark environment at 25 c . the values specified are at an approximate distance 50cm fr om the lcd surface at a viewing angle of f and q equal to 0 . fig. 1 presents additional information concerning t he measurement equipment and method. ver. 0.2 mar. 04, 2009 14 / 28 parameter symbol values units notes min typ max contrast ratio cr 400 - - 1 surface luminance, white l wh 170 200 - cd/m 2 2 luminance variation d white - 1.4 1.6 3 response time tr r + tr d - 16 25 ms 4 color coordinates red rx ry green gx gy blue bx by white wx wx 0.283 0.313 0.343 wy wy 0.299 0.329 0.359 viewing angle 5 x axis, right( f =0 ) q r 30 - - degree x axis, left ( f =180 ) q l 30 - - degree y axis, up ( f =90 ) q u 10 - - degree y axis, down ( f =270 ) q d 20 - - degree gray scale 2.2 6 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display note) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the average of 5 point acro ss the lcd surface 50cm from the surface with all pixels displaying white. for more information see fig 1. l wh = average(l 1 ,l 2 , l 5 ) 3. the variation in surface luminance , the panel t otal variation ( d white ) is determined by measuring l n at each test position 1 through 13 and then defined as followed numerical formula. for more information see fig 2. maximum(l 1 ,l 2 , l 13 ) d white = minimum(l 1 ,l 2 , l 13 ) 4. response time is the time required for the displ ay to transition from white to black (rise time, tr r ) and from black to white(decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determine d for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the ver. 0.2 mar. 04, 2009 15 / 28 gray level luminance [%] (typ) l0 l7 l15 l23 l31 l39 l47 l55 l63 for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4. 6. gray scale specification * f v = 60hz www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display fig. 3 response time the response time is defined as the following figur e and shall be measured by switching the input sign al for black and white. tr r tr d 100 % fig. 2 luminance : active area a : h/4 mm b : v/4 mm points: 13 points h,v active area 1 3 2 5 4 h a b v 6 7 8 9 10 11 12 13 10mm 10mm ver. 0.2 mar. 04, 2009 16 / 28 100 90 10 0 optical response white black white fig. 4 viewing angle normal y eye f q f = 0 , right f = 180 , left f = 270 , down f = 90 , up www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 5. mechanical characteristics the contents provide general mechanical characteristics f or the model lp101wh1. in addition the figures in the next page are detailed mechanical drawing of the lcd. outline dimension horizontal 235.0 0.5 mm vertical 143.0 0.5 mm thickness 5.2mm (max) bezel area horizontal 226.00 mm vertical 128.70 mm active display area horizontal 222.73 mm vertical 125.22 mm weight 200g (max.) surface treatment glare treatment of the front polarizer ver. 0.2 mar. 04, 2009 17 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display note) unit:[mm], general tolerance: 0.5mm ver. 0.2 mar. 04, 2009 18 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display note) unit:[mm], general tolerance: 0.5mm ver. 0.2 mar. 04, 2009 19 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display * mounting screw length (a) = 1.5(min) /1.8(max) * mounting screw hole depth (b) = 1.8(min) * mounting hole location : 2.8(typ.) * torque : 2.0 kgf.cm(max) (measurement gauge : torque meter) section a-a [ detail description of side mounting screw ] notes : 1. screw plated through the method of non-ele ctrolytic nickel plating is preferred to reduce possibility that results in vertical and/or hor izontal line defect due to the conductive particles from screw surface. ver. 0.2 mar. 04, 2009 20 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 6. reliability environment test condition { result evaluation criteria } no. test item conditions 1 high temperature storage test ta= 60 c, 240h 2 low temperature storage test ta= -20 c, 240h 3 high temperature operation test ta= 50 c, 50%rh, 240h 4 low temperature operation test ta= 0 c, 240h 5 vibration test (non-operating) sine wave, 10 ~ 500 ~ 10hz, 1.5g, 0.37oct/min 3 axis, 1hour/axis 6 shock test (non-operating) half sine wave, 180g, 2m s one shock of each six faces(i.e. run 180g 6ms for all six faces) 7 altitude operati ng storage / shipment 0 ~ 10,000 feet (3,048m) 24hr 0 ~ 40,000 feet (12,192m) 24hr ver. 0.2 mar. 04, 2009 21 / 28 { result evaluation criteria } there should be no change which might affect the pr actical display function when the display quality test is conducted under normal operating condition. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 7. international standards 7-1. safety 7-2. emc a) ansi c63.4 methods of measurement of radio-noise emissi ons from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. america n national standards institute(ansi), 1992 b) c.i.s.p.r limits and methods of measurement of radio int erface characteristics of information technology equipment. international special commit tee on radio interference. c) en 55022 limits and methods of measurement of radio interface characteristics of information a) ul 60950-1:2003, first edition, underwriters lab oratories, inc., standard for safety of information technology equip ment. b) can/csa c22.2, no. 60950-1-03 1 st ed. april 1, 2003, canadian standards association, standard for safety of information technology equip ment. c) en 60950-1:2001, first edition, european committee for electrotechnical standardiza tion(cenelec) european standard for safety of information technol ogy equipment. ver. 0.2 mar. 04, 2009 22 / 28 c) en 55022 limits and methods of measurement of radio interface characteristics of information technology equipment. european committee for elect rotechnical standardization.(cenelec), 1998 ( including a1: 2000 ) www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 8. packing 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f ~ m : serial no. note 1. year 2. month mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 nov month oct jun jul aug sep apr may dec mar feb jan ver. 0.2 mar. 04, 2009 23 / 28 b mark a 6 7 8 9 4 5 c 3 2 1 b) location of lot mark serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form a) package quantity in one box : 40 pcs b) box size : 395mm 390mm 309mm www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display 9. precautions please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneve n force (ex. twisted stress) is not applied to t h e module. and the case on which a module is mounted should have s ufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cove r case are not desirable because the former generates corrosive gas of attacking the polarizer at high t emperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glas s, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy c loth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with a bsorbent cotton or other soft materials like chamois soaks with petroleum benzene . normal - hexane is recommended for cleaning the adhesives ver. 0.2 mar. 04, 2009 24 / 28 chamois soaks with petroleum benzene . normal - hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, to luene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their l ong time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperature chang e. condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppres sion to the electromagnetic interference shall be done by system manufacturers. grounding and shielding meth ods may be important to minimized the interference. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display since a module is composed of electronic circuits, it is not s trong to electrostatic discharge. make certain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure 9-5. storage (1) when the protection film is peeled off, static electricity is generated between the film and polar izer. this should be peeled off slowly and carefully by p eople who are electrically grounded and with well 9-6. handling precautions for protection film when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunl ight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. ver. 0.2 mar. 04, 2009 25 / 28 this should be peeled off slowly and carefully by p eople who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarize r with a small amount of glue. if some stress is ap plied to rub the protection film against the polarizer du ring the time you peel off the film, the glue is ap t to remain on the polarizer. please carefully peel off the protection film witho ut rubbing it against the polarizer. (3) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the polarizer af ter the protection film is peeled off. (4) you can remove the glue easily. when the glue r emains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cot ton waste or other soft material like chamois soaked with normal-hexane. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 1/3 byte (dec) byte (hex) field name and comments value (hex) value (bin) 0 00 header 00 00000000 1 01 header ff 11111111 2 02 header ff 11111111 3 03 header ff 11111111 4 04 header ff 11111111 5 05 header ff 11111111 6 06 header ff 11111111 7 07 header 00 00000000 8 08 eisa manufacture code ( 3 character id ) lgd 30 00110000 9 09 eisa manufacture code (compressed asc ) e4 11100100 10 0a panel supplier reserved - product code 0207h 07 00000111 11 0b ( hex. lsb first ) 02 00000010 12 0c lcd module serial no - preferred but optional ("0" if not used) 00 00000000 13 0d lcd module serial no - preferred but optional ("0" if not used) 00 00000000 14 0e lcd module serial no - preferred but optional ("0" if not used) 00 00000000 15 0f lcd module serial no - preferred but optional ("0" if not used) 00 00000000 16 10 week of manufacture 0 weeks 00 00000000 17 11 year of manufacture 2009years 13 00010011 18 12 edid structure version # = 1 01 00000001 19 13 edid revision # = 3 03 00000011 20 14 video input definition = digital signal 80 10000000 21 15 max h image size (rounded cm) = 22 cm 16 00010110 22 16 max v image size (rounded cm) = 13 cm 0d 00001101 23 17 display gamma = (gamma*100)-100 = example:(2.2*100) -100=120 = 2.2 gamma 78 01111000 header vendor / product edid version display parameters ver. 0.2 mar. 04, 2009 26 / 28 24 18 feature support (no_dpms, no_active off/very low po wer, rgb color display, timing blk 1,no_ gtf) 0a 00001010 25 19 red/green low bits (rxry/gxgy) bf 10111111 26 1a blue/white low bits (bxby/wxwy) 45 01000101 27 1b red x rx = 0.584 95 10010101 28 1c red y ry =0.347 58 01011000 29 1d green x gx = 0.323 52 01010010 30 1e green y gy =0.542 8a 10001010 31 1f blue x bx = 0.157 28 00101000 32 20 blue y by = 0.145 25 00100101 33 21 white x wx =0.313 50 01010000 34 22 white y wy =0.329 54 01010100 35 23 established timing 1 (00h if not used) 00 00000000 36 24 established timing 2 (00h if not used) 00 00000000 37 25 manufacturer's timings (00h if not used) 00 00000000 38 26 standard timing id1 (01h if not used) 01 00000001 39 27 standard timing id1 (01h if not used) 01 00000001 40 28 standard timing id2 (01h if not used) 01 00000001 41 29 standard timing id2 (01h if not used) 01 00000001 42 2a standard timing id3 (01h if not used) 01 00000001 43 2b standard timing id3 (01h if not used) 01 00000001 44 2c standard timing id4 (01h if not used) 01 00000001 45 2d standard timing id4 (01h if not used) 01 00000001 46 2e standard timing id5 (01h if not used) 01 00000001 47 2f standard timing id5 (01h if not used) 01 00000001 48 30 standard timing id6 (01h if not used) 01 00000001 49 31 standard timing id6 (01h if not used) 01 00000001 50 32 standard timing id7 (01h if not used) 01 00000001 51 33 standard timing id7 (01h if not used) 01 00000001 52 34 standard timing id8 (01h if not used) 01 00000001 53 35 standard timing id8 (01h if not used) 01 00000001 display parameters panel color coordinates establ ished timin standard timing id www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 2/3 byte (dec) byte (hex) field name and comments value (hex) value (bin) 54 36 pixel clock/10,000 (lsb) 72.3 mhz @ 59.97hz 3e 00111110 55 37 pixel clock/10,000 (msb) 1c 00011100 56 38 horizontal active (lower 8 bits) 1366 pixels 56 01010110 57 39 horizontal blanking(thp-ha) (low er 8 bits) 16 0 pixels a0 10100000 58 3a horizontal active / horizontal blanking(thp-ha) (up per 4:4bits) 50 01010000 59 3b vertical avtive 768 lines 00 00000000 60 3c vertical blanking (tvp-ha) (de blanking typ.for de only panels) 22 lines 16 00010110 61 3d vertical active : vertical blanking (tvp-ha) (up per 4:4bits) 30 00110000 62 3e horizontal sync. offset (thfp) 48 pixels 30 00110000 63 3f horizontal sync pulse width (hspw) 32 pixels 20 00100000 64 40 vertical sync offset(tvfp) : sync width (vspw) 3 lines : 5 lines 35 00110101 65 41 horizontal vertical sync offset/width (upp er 2bits) 00 00000000 66 42 horizontal image size (mm) 224 mm e0 11100000 67 43 vertical image size (mm) 126 mm 7e 01111110 68 44 horizontal image size / vertical image size 00 00000000 69 45 horizontal border = 0 (zero for notebook lcd) 00 00000000 70 46 vertical border = 0 (zero for notebook lcd) 00 00000000 71 47 non-interlace, normal display, no stereo, digital s eparate ( vsync_neg, hsync_pos ), de only note : lsb is set to '1' if panel is de-timing only. h/v c an be ignored. 1b 00011011 72 48 flag 00 00000000 73 49 flag 00 00000000 74 4a flag 00 00000000 75 4b data type tag (descriptor defined by manufacturer ) 00 00000000 76 4c flag 00 00000000 timing descriptor #1 ver. 0.2 mar. 04, 2009 27 / 28 76 4c flag 00 00000000 77 4d descriptor defined by manufacturer 00 00000000 78 4e descriptor defined by manufacturer 00 00000000 79 4f descriptor defined by manufacturer 00 00000000 80 50 descriptor defined by manufacturer 00 00000000 81 51 descriptor defined by manufacturer 00 00000000 82 52 descriptor defined by manufacturer 00 00000000 83 53 descriptor defined by manufacturer 00 00000000 84 54 descriptor defined by manufacturer 00 00000000 85 55 descriptor defined by manufacturer 00 00000000 86 56 descriptor defined by manufacturer 00 00000000 87 57 descriptor defined by manufacturer 00 00000000 88 58 descriptor defined by manufacturer 00 00000000 89 59 descriptor defined by manufacturer 00 00000000 90 5a flag 00 00000000 91 5b flag 00 00000000 92 5c flag 00 00000000 93 5d data type tag ( ascii string ) fe 11111110 94 5e flag 00 00000000 95 5f ascii string l 4c 01001100 96 60 ascii string g 47 01000111 97 61 ascii string 20 00100000 98 62 ascii string d 44 01000100 99 63 ascii string i 69 01101001 100 64 ascii string s 73 01110011 101 65 ascii string p 70 01110000 102 66 ascii string l 6c 01101100 103 67 ascii string a 61 01100001 104 68 ascii string y 79 01111001 105 69 manufacturer p/n(if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 0a 00001010 106 6a manufacturer p/n(if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 20 00100000 107 6b manufacturer p/n(if<13 char--> 0ah, then terminate with asc code 0ah,set remaining char = 20h) 20 00100000 timing descriptor #3 timing descriptor #2 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification lp101wh1 liquid crystal display appendix a. enhanced extended display identificatio n data (eedid tm ) 3/3 byte (dec) byte (hex) field name and comments value (hex) value (bin) 108 6c flag 00 00000000 109 6d flag 00 00000000 110 6e flag 00 00000000 111 6f data type tag ( monitor name, stored as ascii ) fc 11111100 112 70 flag 00 00000000 113 71 monitor name, stored as ascii l 4c 01001100 114 72 monitor name, stored as ascii p 50 01010000 115 73 monitor name, stored as ascii 1 31 00110001 116 74 monitor name, stored as ascii 0 30 00110000 117 75 monitor name, stored as ascii 1 31 00110001 118 76 monitor name, stored as ascii w 57 01010111 119 77 monitor name, stored as ascii h 48 01001000 120 78 monitor name, stored as ascii 1 31 00110001 121 79 monitor name, stored as ascii - 2d 00101101 122 7a monitor name, stored as ascii t 54 01010100 123 7b monitor name, stored as ascii l 4c 01001100 124 7c monitor name, stored as ascii a 41 01000001 125 7d monitor name, stored as ascii 1 31 00110001 126 7e extension flag (# of optional 128 panel id extensio n block to follow, typ = 0) 00 00000000 127 7f check sum (the 1-byte sum of all 128 bytes in this panel id block shall = 0) f1 11110001 timing descriptor #4 checksum ver. 0.2 mar. 04, 2009 28 / 28 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of LP101WH1-TLA1

	To Download LP101WH1-TLA1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .